ABB RDNA-01 Manual do Utilizador Página 232
- Página / 320
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
232 ACS550-01/U1 User’s Manual
Fieldbus adapter
Configuration details depend on the protocol and profile used.These details are
provided in a user’s manual supplied with the FBA module.
Details for the ABB Drives profile (which apply for all protocols) are provided in
section ABB Drives profile technical data on page 242.
Control interface
In general, the basic control interface between the fieldbus system and the drive
consists of:
• Output Words:
–
CONTROL WORD
–
REFERENCE (speed or frequency)
– Others: The drive supports a maximum of 15 output words. Protocols limits
may further restrict the total.
• Input Words:
–
STATUS WORD
– Actual Value (speed or frequency)
– Others: The drive supports a maximum of 15 input words. Protocols limits may
further restrict the total.
Note: The words “output” and “input” are used as seen from the fieldbus controller
point of view. For example an output describes data flow from the fieldbus controller
to the drive and appears as an input from the drive point of view.
The meanings of the controller interface words are not restricted by the ACS550.
However, the profile used may set particular meanings.
Control Word
The
CONTROL WORD is the principal means for controlling the drive from a fieldbus
system. The fieldbus controller sends the
CONTROL WORD to the drive. The drive
switches between states according to the bit-coded instructions in the
CONTROL
WORD. Using the CONTROL WORD requires that:
• The drive is in remote (REM) control.
Fieldbus
Fieldbus controller
Control Word (CW)
References
Status Word (SW)
Actual Values
Parameter R/W Requests/Responses
Process I/O
Service
Messages
(Acyclic)
(cyclic)
- User’s Manual 1
- ACS550-01 Drives (0.75 1
- ACS550-U1 Drives (1 1
- List of related manuals 2
- ACS550-01/U1 Drives 3
- 0.75…160 kW 3
- 1…200 hp 3
- Use of warnings and notes 5
- 6 ACS550-01/U1 User’s Manual 6
- 8 ACS550-01/U1 User’s Manual 8
- ACS550-01/U1 User’s Manual 9 9
- 10 ACS550-01/U1 User’s Manual 10
- Table of contents 10
- Installation 11
- Preparing for installation 12
- ACS550-01/U1 User’s Manual 13 13
- ACS550-01-08A8-4+J404+… 13
- 14 ACS550-01/U1 User’s Manual 14
- ACS550-01/U1 User’s Manual 15 15
- Installing the drive 16
- ACS550-01/U1 User’s Manual 17 17
- 18 ACS550-01/U1 User’s Manual 18
- ACS550-01/U1 User’s Manual 19 19
- 20 ACS550-01/U1 User’s Manual 20
- ACS550-01/U1 User’s Manual 21 21
- R5 and R6 22
- ACS550-01/U1 User’s Manual 23 23
- Control terminals table 24
- ACS550-01/U1 User’s Manual 25 25
- 26 ACS550-01/U1 User’s Manual 26
- ACS550-01/U1 User’s Manual 27 27
- 28 ACS550-01/U1 User’s Manual 28
- ACS550-01/U1 User’s Manual 29 29
- 30 ACS550-01/U1 User’s Manual 30
- Check installation 31
- 32 ACS550-01/U1 User’s Manual 32
- How to start up the drive 33
- 34 ACS550-01/U1 User’s Manual 34
- ABB Motors 35
- 36 ACS550-01/U1 User’s Manual 36
- ACS550-01/U1 User’s Manual 37 37
- 38 ACS550-01/U1 User’s Manual 38
- ACS550-01/U1 User’s Manual 39 39
- REQUEST) 40
- ACS550-01/U1 User’s Manual 41 41
- 42 ACS550-01/U1 User’s Manual 42
- Control panels 43
- 1200 RPM 44
- 405 dm3/s 44
- ACS550-01/U1 User’s Manual 45 45
- 46 ACS550-01/U1 User’s Manual 46
- How to get help 47
- 48 ACS550-01/U1 User’s Manual 48
- ACS550-01/U1 User’s Manual 49 49
- 50 ACS550-01/U1 User’s Manual 50
- PARAMETERS 51
- ASSISTANTS 51
- CHANGED PAR 51
- ABB STANDARD 51
- 52 ACS550-01/U1 User’s Manual 52
- 54 ACS550-01/U1 User’s Manual 54
- ACS550-01/U1 User’s Manual 55 55
- 19.03.05 59
- 60 ACS550-01/U1 User’s Manual 60
- Basic Control Panel 64
- ACS550-01/U1 User’s Manual 65 65
- 66 ACS550-01/U1 User’s Manual 66
- ACS550-01/U1 User’s Manual 67 67
- Reference mode 68
- ACS550-01/U1 User’s Manual 69 69
- 70 ACS550-01/U1 User’s Manual 70
- ACS550-01/U1 User’s Manual 71 71
- 72 ACS550-01/U1 User’s Manual 72
- Application macros 73
- ABB Standard macro 74
- 3-wire macro 75
- Alternate macro 76
- ALTERNATE) 76
- Motor Potentiometer macro 77
- MOTOR POT) 77
- Hand-Auto macro 78
- HAND/AUTO) 78
- PID Control macro 79
- PID CONTROL) 79
- PFC macro 80
- PFC CONTROL) 80
- Torque Control macro 81
- TORQUE CTRL) 81
- 82 ACS550-01/U1 User’s Manual 82
- User parameter sets 83
- USER S1 SAVE) 83
- USER S1 LOAD) 83
- 84 ACS550-01/U1 User’s Manual 84
- ACS550-U1 85
- 86 ACS550-01/U1 User’s Manual 86
- 88 ACS550-01/U1 User’s Manual 88
- ACS550-01/U1 User’s Manual 89 89
- 90 ACS550-01/U1 User’s Manual 90
- ACS550-01/U1 User’s Manual 91 91
- 92 ACS550-01/U1 User’s Manual 92
- ACS550-01/U1 User’s Manual 93 93
- 94 ACS550-01/U1 User’s Manual 94
- ACS550-01/U1 User’s Manual 95 95
- 96 ACS550-01/U1 User’s Manual 96
- ACS550-01/U1 User’s Manual 97 97
- 98 ACS550-01/U1 User’s Manual 98
- ACS550-01/U1 User’s Manual 99 99
- Parameters 100
- Group 99: START-UP DATA 102
- • set up the drive 102
- • enter motor information 102
- Group 01: OPERATING DATA 104
- Group 03: FB ACTUAL SIGNALS 108
- Group 04: FAULT HISTORY 110
- REF1 and REF2 113
- Group 13: ANALOG INPUTS 119
- Group 14: RELAY OUTPUTS 120
- Group 16: SYSTEM CONTROLS 125
- Group 20: LIMITS 129
- Group 21: START/STOP 132
- Group 22: ACCEL/DECEL 135
- Group 23: SPEED CONTROL 137
- Group 24: TORQUE CONTROL 139
- Group 25: CRITICAL SPEEDS 140
- Group 26: MOTOR CONTROL 141
- Group 29: MAINTENANCE TRIG 143
- Group 30: FAULT FUNCTIONS 144
- Group 31: AUTOMATIC RESET 148
- Group 32: SUPERVISION 149
- Group 33: INFORMATION 151
- Group 34: PANEL DISPLAY 152
- FAULT FUNCTIONS 156
- Group 37: USER LOAD CURVE 162
- PID 1 PARAM SET 173
- SAVED KWH, 0175 SAVED MWH 176
- Group 51: EXT COMM MODULE 178
- Group 52: PANEL COMM 180
- Group 53: EFB PROTOCOL 181
- Group 98: OPTIONS 198
- Embedded fieldbus 199
- Planning 200
- Communication set-up – EFB 201
- COMM PROT SEL = 201
- STD MODBUS) 201
- PID control setpoint source 206
- Communication fault 206
- Feedback from the drive – EFB 207
- Diagnostics – EFB 208
- COMM FAULT TIME 210
- ACTUAL VALUES and are: 218
- ABB Drives profile 220
- DCU Profile 221
- Status Word 222
- The contents of the 222
- DCU profile 224
- ABB DRV LIM 226
- CONTROL WORD (CW) 227
- Fieldbus adapter 231
- Communication set-up – FBA 235
- COMM PROT SEL. Set 9802 235
- EXT FBA) 235
- Feedback from the drive – FBA 238
- Diagnostics – FBA 239
- CONTROL WORD is 242
- STATUS WORD (SW) bits 245
- Diagnostics 253
- ALARM 2008 254
- Fault resetting 259
- Correcting alarms 260
- Alarm listing 261
- Maintenance 265
- Main fan replacement 266
- Capacitors 269
- Control panel 269
- Technical data 271
- Ratings, 380…480 V drives 272
- Input power connections 275
- Motor connections 283
- EARTH FAULT 286
- Brake components 289
- DISABLE)] 292
- Control connections 293
- Efficiency 294
- Air flow, 208…240 V drives 295
- Air flow, 380…480 V drives 295
- Air flow, 500…600 V drives 296
- Dimensions and weights 297
- Outside dimensions 298
- Degrees of protection 300
- Ambient conditions 300
- Materials 301
- Applicable standards 303
- CE marking 303
- C-Tick marking 303
- UL/CSA markings 304
- MOT THERM PROT) 304
- MOT THERM RATE) 304
- Product protection in the USA 306
- Numerics 307
- Further information 319
- EFFECTIVE: 2009-07-07 320
Manuais e produtos relacionados com não ABB RDNA-01
não ABB SPA-ZC 400 Manual de Serviço
(76 páginas)
(76 páginas)
não ABB SPA-ZC 402 Manual de Serviço
(88 páginas)
(88 páginas)
não ABB Tina 7A Manual de Serviço
(56 páginas)
(56 páginas)
não ABB RDNA-01 Manual do Utilizador
(348 páginas)
(348 páginas)
não ABB Tina 7A Manual de Serviço
(12 páginas)
(12 páginas)
não ABB FENA-01 Manual do Utilizador
(34 páginas)
(34 páginas)
não ABB FPBA-01 Especificações
(21 páginas)
(21 páginas)
não ABB AW400 Series Manual do Utilizador
(8 páginas)
(8 páginas)
não ABB FENA-21 Manual do Utilizador
(46 páginas)
(46 páginas)
não ABB MicroFlex e150 Manual de Instalação
(7 páginas)
(7 páginas)
não ABB RECA-01 Manual do Utilizador
(6 páginas)
(6 páginas)
não ABB FDNA-01 Manual do Utilizador
(460 páginas)
(460 páginas)
não ABB RDNA-01 Manual do Utilizador
(330 páginas)
(330 páginas)
não ABB Tina 7A Manual de Serviço
(62 páginas)
(62 páginas)
não ABB RDNA-01 Manual do Utilizador
(302 páginas)
(302 páginas)
não ABB Tina 7A Manual do Utilizador
(44 páginas)
(44 páginas)
não ABB ML82PH Manual do Utilizador
(29 páginas)
(29 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais