ABB HTP500 Guia do Utilizador

User guide HTP500 V2 Thermal transfer printer

Inside details front part of the Printer Back Part of the Printer In the Printer back part are presents: CE Marking

1.3 IMPORTANT SAFETY INFORMATION Always observe the following warnings and cautions for a safe and correct use of HTP500 V2. 1.3.1 Printer Setup Loca

1.3.2 Power Supply Remember any electrical equipment can cause injury if not handled properly. Make sure to observe the

1.3.3 External Cleaning of the Printer Always clean the printer when it is turned off and not plugged to Power. Use a dry fabric or a little wet tiss

 Find out a flat surface on which position the printer, on its destination place, before to move the printer itself  Make sure that all the printe

Print speed Plate: 30mm/sec, Acryl mode: 20mm/sec, Automatic : 20mm/sec Guaranteed print area Size: width 54mm; length 496mm Ribbon Ribbon cartridg

 LEDS POWER: Lights when you turn on the power switch ONLINE: Lights when the printer is ready to receive data and flashes when the printer is

REMOVE to clear a jam or to eject a printer media Use always the [MENU/ ] and [ ] keys, located on the control panel, to select among the printe

2.4 LOADING / REMOVING THE CLEANING CASSETTE 2.4.1 Loading of the Cleaning Cassette HTP500 V2 has a special cleaning cassette purposely designed to

HTP500 V2 User Guide Contents CONTENTS ...

5) Set the cleaning cassette along the guides passing the cleaning cassette tape around the cleaning auxiliary roller. 6) Raise the setting lever

2.5 LOADING A RIBBON CASSETTE Load a ribbon cassette performing the instructions shown in the pictures below. 1) Remove the ribbon cassette stoppe

2) Press the (I) side of the power switch to turn on the printer. The power led on the control panel lights. 3) After the printer performance of its i

3 – DRIVER AND SOFTWARE INSTALLATION Here following the step by step instructions for the HTS500 Software installation and creation of

Please go on www.swactivation.com in order to get the licence numbers. 1) The program asks to read the Precode and Code. 2) The program ask to f

Select the subfolder \Drivers Select the subfolder \HTP500V2 Execute the file Setup.exe, select your preferred language, press Install The process be

Press Continue Anyway The PC should be restarted Press OK Press Finish Remind: With the printer switched off connect the printer to the PC

Switch the printer on Windows detects a new hardware Go on with the guided installation of the new Hardware. Press Next Press Next Press Con

Press Finish The printer has been detected and has been added among the printers available in the folder printer and faxes with the name P-PRINTER

D) Copy Installation of the 6 Printing Devices for Windows XP Restart the PC, connect the HTP500 V2 to the USB port and switch on the printer. Sele

7.5 CLEANING AND STORING PLATES ... 62 7.6 TEST PRINT ...

Press OK Into the Devices and Printers folder you will find the file of origin P-PRINTER and the 6 devices installed with the following names:

Select Properties The Window for the Selection of the profiles appears. Select the Profiles Folder. The Window with the Pre-set Profiles appears.

Select the AUTOM CABLES Profile. Press the Retrieve button. The Window for the Confirmation of the Profiles appears. Press Yes button to Confirm.

Press Ok to Confirm. The Window for setting the Multiple Device Setting appears. Press the Centering button. The following window appears. Selec

F) Table of Printer Devices and Pre-set Profiles Pre-set profiles contain the Printer Device Parameters: PRINTER DEVICE NAME created in WINDOWS PRE

Press Next Select the first Option: I accept the items of the license agreement Press Next Verify that the Printer is not connected to the PC. P

Press Install the Software Driver The PC must be turned off and restart. Press OK. The PC turns off and restarts. The PC must be Turned Off a

A new hardware found message appears. The Driver Installation proceeds. The System Detected the Printer. The Printer had been detected

It appears the window that indicate the assigned USB port for the PLATE PRINTER. Press OK Press OK Into the Devices and Printers folder you wil

Select the Menu Plotter Setup. It appears the Setup Plotters/Printers window Select the button on the Left in the First raw that is available in th

INTRODUCTION Thank you for choosing HTP500 V2! HTP500 V2 will help you marking fast and easy. To ensure HTP500 V2 best performances, read this manual

Select the AUTOMATIC CABLES Profile. Press the Retrieve button. It appears the window for the Confirmation of the Profiles Press Yes to Confi

F) Table of Printer Devices and Pre-set Profiles Pre-set profiles that contains the Printer Device Parameters. PRINTER DEVICE NAME created in WIND

a.5) Create a single-item job inserting as text ‘HHHHHH’ in the first tag. a.6) Print the job a.7) Verify the centering of the first tag. a.8) a) Exa

a.8.2) After the item description in the parentheses there is the reference measure of the printed area (220 mm): a.8.3) In the X field type in the v

Select your language Press Install Select Remove all Installed features Press Next Press Yes button. After the elaboration, The PC mus

TERMINAL BLOCKS HTP500 V2 HORIZ METHACRYLATE MMA HORIZONTAL Plates 60 x 500 (mm) Horizontal Plate Name Manual 1 3 HTP500 V2 HORIZ PVC LABELS PVC HORIZ

4 – PRINTS OF TAGS WITH AUTOMATIC FEEDER IN “STACK” Feeder Mode This shows how to print Automatically the cable tags with HTP500 V2 easily and quickly

NOTICE  Do not tight too much the locking screw A so not to damage it. Do not loosen too much the docking screw A but just enough to fix the gui

Fix the B screw of the Card Store so that the mobile part of the Card Store indicated with the arrow lets to pass just one module to be printed. It ca

And afterwards the following message Take the “Support Plate” carefully and insert it beneath the “Card Store” till the mobile part is

Keep this manual for future reference! This document will support you during the use of the ABB HTP500 V2 Plate Printer. Please read the warnings care

5 - PRINTS OF TERMINAL BLOCK TAGS in “SINGLE” Feeder Mode This section explains how to print with the HTP500 V2 easily and quickly. Execute all the de

The HTP500-PL3 Support Plate for the T-Blocks tag should be inserted in the HTP500 V2 printer in the way that the encoder, underneath the support plat

And afterwards the following message Bring the “Support Plate TB” with a module of T-Block tags positioned on and insert it carefully till the

6.2 INSERTING THE MODULES ON THE PRINTER 1) Place a plate on the feeding table and align the edge with the cleaning brush. 2) Adjust the wid

3) Tighten the locking screw securing the width guides in the right position. 4) Insert the plate into the feed opening until the printer beeps.

The printer detects the Tag or Strip (if it is already on the plane of the printer) and moves it in the correct HOME position READY FOR THR PRINT. 6.

1) Press [Menu/ ] 2) Press [Menu/ ] and [ ] to display “Auto Off” 3) Press ENTER 4) Press [Menu/ ] and [ ] to change selection (off to delete the opt

JAMMED PLATE Utilize only the “MENU – REMOVE” function to eject the item from the printer. Press “ONLINE” and then “MENU” With the right arrow select

 Are the width guides adjusted properly? Adjust the width guides so that they can hold properly the plate  Dirty or slipping rollers? Clean care

The print stops before the plate end Verify that in the driver it is set the correct print area. For Ex., if in the driver it has been set a print are

 Don’t set this printer up close to alcohol, paint thinner and other flammable chemicals  Don’t use flammable sprays close to the printer  When

Insert Feeder At started print the printer warn that no support plate for the items has been inserted. Insert the correct support plate in the printer

One of the printer components may be damaged. Ask ABB Technical Assistance. 7.4 DAILY CARE A careful daily care helps to keep HTP500 V2 in good cond

7.4.2 OTHER PARTS TO CLEAN Before using the printer check it and clean it as described below. Print head Clean the print head using a blower, soft cl

For this reason it is recommended to observe the instructions listed below:  Store plates in plastic bags to protect them from dust and dirt.  Pla

8 – PACKAGING AND TRANSPORTATION The Printer HTP500 V2 complete with:  MANUAL  SI2K0003 – CLEANING ROLLER  RIB-B – Strong Black Ribbon.  USB C

feeder in « STACK » feeder mode Mandatory Support plate to print the cable tags ABB Terminal-block tags To print with automatic feeder in « STACK »

1SNC160010M0202 – 10.2012

WARNING  Do not wait until the components (e.g. support plate, roller, etc.) are worned to before to proceed with the substitution. We suggest

1 - BEFORE USE This chapter is written as an introduction to the HTP500 V2. The chapter contains four sections as follows: 1.1 Accessories 1.2 Iden

1.2 IDENTIFICATION OF THE PRINTER PARTS Printer Front Part